No products in the cart.
MAKE A STATEMENT
UP TO 20% OFF
ESKOM
We'll bring it to life. ONLY R17 / hour
Product Carousel Tabs
VR Gadgets
HTC Vive Desk Stand
HTC Vive desk stand including controller and it is possible to charge the controllers while on the stand.
Weights aprox. 350g and it is very stable, the base is 180x180mm and you need aprox 250x250mm of desk space to have this on your desk.
You need:
2 M4 or M5 screws
2 washers (i used 4 to get some height because I had long screws)
SKU: 2412007
Load Shedding
12V Router & WiFi UPS (2 Outputs)
With load shedding kicking into full gear again, keep your internet and WiFi running during outages, even with 2 load shedding periods
Unlike other router/wifi UPS out there, ours are South African made (local is lekker), we use quality Samsung batteries and not high cap fake batteries that can be a fire hazard and our device has 2 ports allowing you to plug in your fiber CPE and your WiFi router at the same time (or any 12V appliance). Remember if you buy cheap Chinese UPS it will mean your capacity will be fake and your charge cycles (thus lifespan of the device) will be less. We use quality batteries that will give you more than 1000 cycles!
We’ve tested a Vumatel CPE/Raycore + Hauwei Wifi router and got over 5 hours run time.
The product is in a really neat small form factor 3D printed in black. Each unit is produced, assembled and tested before sending out.
HOW DOES IT WORK?
The provided plug gets plugged into the wall to charge the UPS, if the power goes out your devices keep running. The connected devices are connected using the provided male to male extensions. So in essence, you won’t use your router, WiFi or 12v appliance’s plug but instead use the included wires to connect them to the UPS. This UPS supports 2 connections thus no need to buy 2 UPS like other brands.
Important: The ports are 5.5×2.1mm – this is most widely used for routers and fiber boxes! You can buy adapters if needed.
SKU: UPS12VX2
COVID-19 Essentials
EZ Face Mask
The Goal of this mask is to make a low poly respirator that is stupid simple operate and that uses a readily available/incredibly cheap filter mechanism requiring no cutting of material. (in this case makeup pads). The cotton pads, from research seems to block about 75% – I add 2x on my (Large) face mask without any need for cutting of the pad. So I receive extra filtration.
We’ll include a elastic type filament strand as the holder of your mask to your head. Which is like a string and so far seems to work fine.
SKU: culmsk
COVID-19 Essentials
EZ Face Shield
This is a quick and easy DIY face shield. Simply clip the clear sheet onto the headband and stretch the elastic into the slits at the back if you need it to grip your head. Everything you need is included in the kit!
If you want to cut the sheet at the bottom to round the corners you can. This product should be used in conjunction with a face mask or with our EZ Face Mask for maximum protection.
SKU: n/a
VR Gadgets
HTC Vive Desk Stand
HTC Vive desk stand including controller and it is possible to charge the controllers while on the stand.
Weights aprox. 350g and it is very stable, the base is 180x180mm and you need aprox 250x250mm of desk space to have this on your desk.
You need:
2 M4 or M5 screws
2 washers (i used 4 to get some height because I had long screws)
SKU: 2412007
3D Printing Service
3D Printing Instant Quote
We’ve been working hard on getting an instant quote solution to customers, so that you can check pricing and buy instantly based off of those quotation instead of contacting us first and having to wait for pricing.
Simply upload your designs and our system will analyze it and calculate the pricing for your parts.
You can find STL files (3D models) on sites like Thingiverse, MyMiniFactory, Cults3D, etc. These files can all be quoted on once you upload them here.
SKU: n/a
COVID-19 Essentials
EZ Face Mask
The Goal of this mask is to make a low poly respirator that is stupid simple operate and that uses a readily available/incredibly cheap filter mechanism requiring no cutting of material. (in this case makeup pads). The cotton pads, from research seems to block about 75% – I add 2x on my (Large) face mask without any need for cutting of the pad. So I receive extra filtration.
We’ll include a elastic type filament strand as the holder of your mask to your head. Which is like a string and so far seems to work fine.
SKU: culmsk
GPU Things
Vertical GPU mounting Bracket
* This design does NOT require any modifications that would damage your case.
* This is only compatible with Full Tower and Mid Tower cases with 6 PCI slots or higher, so compatibility is buyer’s responsibility.
* It requires 6 screws on the side and 4 at the back of the case to firmly secure the mount in place.
SKU: 2838403
![218844260c82bd4cd53a9ec465f01ab0_preview_featured[1]](https://shap3d.co.za/wp-content/uploads/2020/02/218844260c82bd4cd53a9ec465f01ab0_preview_featured1-100x100.jpg "218844260c82bd4cd53a9ec465f01ab0_preview_featured[1]")
Best Sellers
Console Gadgets
Playstation Things
PS4 SLIM wall mount
Use at own risk 😉
I have made every effort to create a useful an discrete mount and as you can see from the pics, it works 🙂
Please note that these mounts will only hold your unit in a horizontal position. If
attached vertically and you slide in the unit vertically, it will slip through and fall.
First, screw or glue the two small rails to the bigger symmetrical L-shaped parts.
I used screws with a flat head, 13mm total length and thread 2,5mm. Connect the mounts with the x-lattice to ensure an accurate distance. Mark the holes on the wall with a pencil through the screw-holes if you have to drill. Type of screw for the wall depends on the wall type. The x-lattice is meant to be removed once the mounts are in place.
Match up the rails with the grooves on either side of your PS4 and slide it horizontally in place 🙂
SKU: 3327508
Playstation Things
PS4 Wall Mount
Mount your Playstation 4 on the wall!
The vents are barely blocked much by this design, so it has that going for it, which is nice.
I wouldn’t recommend this for horizontal mounting (e.g., under a shelf). The little bumps are there to hold the PS4 in place, not to support its full weight. The chunky shelf part takes the weight. Mounting horizontally would put all the load on the little nubbinses, which could be a disaster.
SKU: 1271753
Get Organized
Smart Home Things
